Description

Key Features

Hot Water Cleaning Power

The Mi-T-M HSE-1502-0MM11 HSE Series 1500 PSI Electric Direct Drive Hot Water Pressure Washer combines 1500 PSI, 2.0 GPM, and a top-fired heat exchanger to break down grease, oil, and packed-on grime faster than cold-water units.

Industrial Electric Drive

The 2.0 HP totally enclosed fan-cooled electric motor is built for indoor or enclosed-area use where engine exhaust is a problem, while manual thermal overload protection helps protect the motor on long cleaning sessions.

Built For Rough Sites

A reinforced powder coated steel frame, center balanced lift, and 13-inch flat-free tires make this pressure washer easier to move around construction sites, farms, and industrial yards without babying it.

Overview

The Mi-T-M HSE-1502-0MM11 HSE Series 1500 PSI Electric Direct Drive Hot Water Pressure Washer is a commercial electric hot water pressure washer built for industrial cleaning where heat matters as much as pressure. This is a hot water pressure washer designed for industrial cleaning on construction sites, farms, mining operations, and oil fields. Model Number: HSE-1502-0MM11. If you are dealing with grease, oil, mud packed with residue, or equipment that needs more than a cold rinse, this unit is aimed at that kind of work.

Its 1500 PSI output and 2.0 GPM flow are matched to a hot water system that delivers a 150 degree Fahrenheit temperature rise above ambient, with published maximum outlet temperature figures ranging from 200 to 225 degrees Fahrenheit depending on source. What matters on the job is simple: the heated water helps cut through oily buildup and stuck-on grime more efficiently, so you spend less time dwelling on the same spot and less time leaning on chemical cleaners.

The drive system is built around a 2.0 HP, 120V electric motor drawing 19.0A. Mi-T-M uses a totally enclosed fan-cooled motor with manual thermal overload protection, which is the right setup for a machine that may run in dirty working environments. The 35-foot power cord gives you useful reach from the outlet to the work area, and the NEMA 5-20P plug tells you this is not a casual household setup. You need the correct 120V, 20A circuit, which is exactly the kind of thing a buyer should know before the unit shows up.

On the pump side, this washer uses a Mi-T-M pump with Pressure Relief Start, a forged brass manifold, a factory preset unloader, and a thermal relief valve. Those are not throwaway specs. Pressure Relief Start is there to reduce startup load in the system, the forged brass manifold is the kind of material you want on a professional machine, and the thermal relief valve helps protect the pump from heat buildup during bypass conditions. In plain terms, it is built with the kind of components that make sense on a machine expected to work, not sit in a garage.

The chassis is just as job-focused. The reinforced powder coated steel frame is built to take bumps and movement around rough surfaces, and the center balanced lift makes it easier to handle when loading or repositioning. The 13-inch flat-free tires are a big plus on gravel, dirt, and uneven concrete because you are not losing time dealing with flats. Mi-T-M also includes practical storage touches like a gun and wand holder and hose wrap, which sound small until you are moving the washer several times a day.

Heating hardware matters on a hot water pressure washer, and this one uses an energy-efficient top-fired heat exchanger with a diesel or kerosene fired burner. It is designed to be accessible for service, which matters more than flashy specs once the machine is in a real maintenance cycle. The burner fuel tank holds 4.0 gallons, and fuel consumption is listed at 1.21 gallons per hour. That gives buyers a realistic sense of operating demand when planning daily use.

This unit is sold as a ready-to-work package with quick connect nozzles in 0 degree, 15 degree, 25 degree, and 40 degree patterns, a 50-foot by 3/8-inch steel wire-braided hose, and an adjustable pressure insulated dual lance with trigger gun. That means you are not starting from scratch hunting for the basics. You have the spray patterns needed for rinsing, concentrated cleaning, and general surface work right out of the crate.

Who should buy it? Contractors, farm operators, maintenance crews, equipment service shops, and industrial users who need electric-powered pressure washing with hot water capability. If your work is mostly light residential washing, this is more machine than you need. If you clean greasy equipment, heavy buildup, or work in spaces where electric drive is a better fit than a gas engine, this Mi-T-M pressure washer makes a lot more sense.

At a Glance

1500 PSI

Cleaning Pressure

2.0 GPM

Water Flow

169,000 BTU

Burner Output

50 ft

Hose Length

Mi-T-M HSE-1502-0MM11 Hot Water Cleaning Setup

This setup is built around practical jobsite use. The long hose, insulated dual lance, and wheeled steel frame make it easier to clean equipment, pads, and work areas without constantly dragging the machine into the mess.

• Includes a 50-foot x 3/8-inch steel wire-braided hose for reach
• Comes with four quick connect nozzles for different spray patterns
• Uses 13-inch flat-free tires for easier movement across rough ground

What’s in the Box

• Quick connect nozzles: 0 degree, 15 degree, 25 degree, and 40 degree
• 50-foot x 3/8-inch steel wire-braided hose
• Adjustable pressure insulated dual lance
• Trigger gun

Key Specifications

Pressure (PSI)	1500 PSI
Water Flow (GPM)	2.0 GPM
Motor	2.0 HP, 120V, single phase, 19.0A
Plug Type	NEMA 5-20P
Burner Output	169,000 BTU per hour
Burner Fuel Tank Capacity	4.0 gal
Burner Fuel Consumption	1.21 GPH
Weight	291 lbs

Built For

Construction Sites Farms Mining Oil Fields Industrial Equipment Cleaning Maintenance Crews

Warranty & Support

7-year Mi-T-M pump warranty, 3-year coil warranty, and 1-year electric motor warranty.

Tool Nut’s Take

Tool Nut’s Take

Heat Does The Heavy Lifting

The Mi-T-M HSE-1502-0MM11 HSE Series 1500 PSI Electric Direct Drive Hot Water Pressure Washer is the kind of machine you buy when cold water is wasting your time.

• Who it’s for: Contractors, farm owners, and industrial users cleaning greasy equipment, work pads, and heavy residue where an electric pressure washer is the better fit.
• Why it stands out: You get hot water capability, a professional Mi-T-M pump setup, a reinforced steel frame, and a ready-to-run hose and nozzle package.
• Worth knowing: This runs on 120V with a NEMA 5-20P plug, so make sure your power supply matches, and it is a serious commercial unit at 291 pounds net weight.

Common Questions

• Is this a cold-water or hot-water pressure washer? This is a hot water pressure washer with a top-fired heat exchanger and diesel or kerosene fired burner.
• What power does it require? It uses a 2.0 HP, 120V, single-phase electric motor that draws 19.0A and uses a NEMA 5-20P plug.
• What kind of cleaning is it built for? Mi-T-M positions this unit for industrial cleaning on construction sites, farms, mining operations, and oil fields.
• How hot does the water get? Published data lists a 150 degree Fahrenheit rise above ambient, with maximum outlet temperature figures listed between 200 and 225 degrees Fahrenheit depending on source.