Description

Key Features

Cleaner Raised Panels

The 2+2 cutting design uses upward and downward shearing cutters to reduce splintering. That matters when you want a cleaner finish on raised panel work with less sanding after the cut.

Replaceable Insert Design

Instead of replacing a full brazed cutter, you can swap insert knives during sharpening cycles. That helps cut tooling cost and keeps downtime under control in production work.

Built for Wood Panels

The Freud UP190-IC V-Paneling Cutter Set is made for producing glass-smooth raised panels in hardwood, softwood, MDF, and plywood. It is a serious shaper cutter for cabinet and door work, not a general-purpose profile bit.

Overview

Freud UP190-IC 4-1/8 in. x 31/32 in. – 1-5/64 in. x 1-1/4 in. V-Paneling Cutter Sets is a shaper cutter set built for raised panel woodworking. This is a shaper cutter designed for producing smooth V-panel raised panels in cabinet doors and furniture components. Model Number: UP190-IC. If you are running a shaper in a serious shop and want cleaner finish quality with lower long-term tooling cost, this cutter is aimed right at that job.

The big story here is Freud’s 2+2 shear cutting layout. Two larger cutters shear upward and two smaller cutters shear downward, which helps control tear-out and leaves a cleaner edge across the grain. In plain terms, the cutter is set up to leave a finish that needs less cleanup, which is exactly what you want when raised panels are going into visible door and casework.

The insert cutter design is another practical advantage. On a busy woodworking line, swapping inserts is a lot easier than replacing an entire brazed cutter assembly. Freud also calls out 2.0 mm thick sharpener-friendly carbide, so the system is built around repeated service instead of being treated like a throwaway cutter. That makes sense for shops trying to keep finish quality high without eating tooling cost every time edges dull out.

Freud uses its TiCo Hi-Density micro-grain carbide for the cutting knives, and that matters because edge quality and wear life are everything on panel work. A sharper edge with less wear means the profile stays consistent longer, and that helps you hold finish quality from the first door to the last one in a run. The superior shear angles are also meant to slice wood fibers cleanly, especially on cross-grain cuts where fuzzy edges and sanding time usually show up fast.

From a build standpoint, the aluminum body gets a red anodized protective coating to resist abrasion. Freud also notes computer balancing with tight tolerances for smoother, chatter-free cutting. On a shaper cutter this size, balance is not a throwaway detail. A well-balanced cutter runs smoother, leaves a better surface, and puts less nonsense into the cut when you are trying to produce repeatable panel profiles.

Safety and control features matter too, and this cutter includes a kickback-reducing shoulder design that restricts tooth bite to 1.1 mm. That helps reduce the effects of overfeeding and supports a more controlled cut. No cutter fixes poor setup or bad feed habits, but this design does give the operator more margin for clean, predictable work.

Compatibility is straightforward and important. This cutter has a 1-1/4 in. bore, and Freud states that all 1-1/4 in. bore cutters can be used with back-cutters UP230-IC and UP231-IC when using 3/4 in. stock. That gives shops a defined path if they want to build out a more complete raised panel setup around matching back-cutting operations.

This Freud shaper cutter is best suited for cabinet shops, door manufacturers, millwork operations, and serious woodworkers using a shaper for panel production. It is also a good fit for enthusiasts who want industrial-style cutter performance and serviceability. If your work is occasional hobby routing on a small table, this is more cutter than you need. If your goal is repeatable raised panel results in hardwood, softwood, MDF, or plywood, this is exactly the kind of tooling that earns its keep.

Built for Shaper-Based Panel Work

This cutter is meant for a shaper setup where finish quality and repeatability matter. The 1-1/4 in. bore and industrial insert-style construction put it in the lane of serious raised panel production, not light trim profiling.

• 1-1/4 in. bore diameter for shaper use
• Computer-balanced body helps support smoother, chatter-free cutting

Handles Common Panel Materials

Freud lists this cutter for hardwood, softwood, MDF, and plywood, which makes it useful for shops that build painted and stain-grade doors from different panel stock. That flexibility is a big deal when material choices change from job to job.

• Suitable for hardwood, softwood, MDF, and plywood
• Ideal for producing raised panels with a glass-smooth finish

Key Specifications

Tool Type	V-Paneling cutter set
Cutter Type	Insert cutter design
Diameter	4-1/8 in.
Carbide Height (H)	31/32 in. to 1-5/64 in.
Cut Depth (C)	19/64 in.
Bore Diameter	1-1/4 in.
Tenon Length (L)	9/32 in.
Tenon Thickness (T)	3/16 in. to 9/32 in.

Compatibility

Shaper Bore

Designed with a 1-1/4 in. bore diameter for matching shaper spindle setups.

Back-Cutter Compatibility

Freud states that all 1-1/4 in. bore cutters can be used with back-cutters UP230-IC and UP231-IC when using 3/4 in. stock.

Workpiece Materials

Suitable for hardwood, softwood, MDF, and plywood panel work.

Built For

CabinetmakingWoodworkingMillworkDoor MakingRaised Panel ConstructionProduction ShopsFurniture ComponentsSerious DIY / Hobbyist

Pro Tip

If you are building 3/4 in. raised panels and want a matched backside relief setup, pair this 1-1/4 in. bore cutter with Freud back-cutters UP230-IC or UP231-IC. It is a cleaner way to keep panel thickness and fit more predictable across a full door run.

Tool Nut’s Take

Tool Nut’s Take

Freud UP190-IC V-Paneling Cutter Set Means Business

This is the kind of raised panel cutter you buy when finish quality, service life, and lower downtime actually matter in the shop.

• Who it’s for: Cabinet shops, millwork guys, and serious woodworkers running a shaper for raised panels in doors, furniture, and architectural work.
• Why it stands out: The 2+2 shear layout, replaceable insert design, TiCo carbide, and balanced body all work toward the same goal: cleaner cuts with less sanding and less interruption when the edge finally needs attention.
• Worth knowing: This is specialized shaper tooling with a 1-1/4 in. bore, so make sure your machine setup matches. It is not a casual, one-size-fits-all profile cutter.

Common Questions

• What kind of tool is this? It is a V-paneling shaper cutter set with an insert cutter design for producing raised panels.
• What materials can it cut? Freud lists hardwood, softwood, MDF, and plywood as suitable materials.
• What bore size does it use? The bore diameter is 1-1/4 in.
• Can it be used with a back-cutter? Yes. Freud states that 1-1/4 in. bore cutters can be used with UP230-IC and UP231-IC back-cutters when using 3/4 in. stock.